Vorige onderwerp :: Volgende onderwerp |
Auteur |
Bericht |
assrar

|
Geplaatst: Zo Feb 10, 2013 10:22 pm Onderwerp: Sixpack with a grey ribbon cable not colored |
|
|
Hi,
I receive the AFDS, But with a grey ribbon cable not colored .
i don't know which way to connect to the AFDS. i took a picture of it so if anybody know how to connect please tell me.
the first or the second one
1-
2-
thanks |
|
Terug naar boven |
|
 |
assrar

|
Geplaatst: Zo Feb 10, 2013 10:24 pm Onderwerp: |
|
|
2-
thanks |
|
Terug naar boven |
|
 |
assrar

|
Geplaatst: Zo Feb 10, 2013 10:41 pm Onderwerp: |
|
|
Sorry all what i meant in the above test is the SIX PACK recall.
But where is the picture gone |
|
Terug naar boven |
|
 |
assrar

|
Geplaatst: Zo Feb 10, 2013 10:44 pm Onderwerp: |
|
|
why i cant edit my posts in this forum  |
|
Terug naar boven |
|
 |
assrar

|
|
Terug naar boven |
|
 |
Engravity_Support


|
Geplaatst: Zo Feb 10, 2013 11:59 pm Onderwerp: |
|
|
if you look at the six packs from the back, the most left pin is the ground for the recal switch. The most right pin is the common cathode for the leds.
You can use the picture below for reference.
http://home.casema.nl/pago/sixb.JPG
if you have a multimeter with a continuity test, measure 2 pins on either end. press one of the recall buttons and see if it closes. if it closes you have found the 2 terminals for the recall. from there you can use the diagram in the manual to see the other connections. _________________ www.flyengravity.com
Build your own jetliner |
|
Terug naar boven |
|
 |
flypast
|
Geplaatst: Ma Feb 11, 2013 12:52 am Onderwerp: |
|
|
Hi Assrar
I've just fitted the six packs quite easily with the grey ribbon cable.
The red one is the common cathode, so it follows that the next cable will connect one of the LED anunciators to your card.
For example cable 1 (common cathode red)
Cable 2 (next to common cathode (red)) will be the APU annunciator
Cable 3 will be the FLT CONT annunciator and so on and so on.
These aren't necessarily the order the the annunciators are wired but hopefully it will give you an idea.
Hope that makes sense.
Alan |
|
Terug naar boven |
|
 |
assrar

|
Geplaatst: Ma Feb 11, 2013 4:56 pm Onderwerp: |
|
|
Thank You Support and thank you flypast,
I will follow you and post the result.
assrar |
|
Terug naar boven |
|
 |
assrar

|
Geplaatst: Di Feb 12, 2013 12:47 pm Onderwerp: |
|
|
Engravity_Support schreef: | if you look at the six packs from the back, the most left pin is the ground for the recal switch. The most right pin is the common cathode for the leds.
You can use the picture below for reference.
http://home.casema.nl/pago/sixb.JPG
if you have a multimeter with a continuity test, measure 2 pins on either end. press one of the recall buttons and see if it closes. if it closes you have found the 2 terminals for the recall. from there you can use the diagram in the manual to see the other connections. |
He Engravity_Support and Mr.Alan,
Just to make sure the wiring is correct before i connect the cable.
Switch
======
cable - board
1-1
2-2
-------------------
LED
===
cable - board
9-1
8-2
7-3
6-4
5-5
4-6
3-7
assrar |
|
Terug naar boven |
|
 |
flypast
|
Geplaatst: Di Feb 12, 2013 4:00 pm Onderwerp: |
|
|
Hi Assrar
what board are you using?
Alan |
|
Terug naar boven |
|
 |
assrar

|
|
Terug naar boven |
|
 |
flypast
|
Geplaatst: Di Feb 12, 2013 11:26 pm Onderwerp: |
|
|
Hi assrar
Looks good to me. Go for it.
Let me know how you get on.
Cheers
Alan |
|
Terug naar boven |
|
 |
Engravity_Support


|
Geplaatst: Vr Feb 15, 2013 2:21 am Onderwerp: |
|
|
yup,
1 (red) + 2 for the switch
3-8 LED anode
9 Led cathode _________________ www.flyengravity.com
Build your own jetliner |
|
Terug naar boven |
|
 |
flypast
|
Geplaatst: Za Feb 16, 2013 8:16 pm Onderwerp: |
|
|
Hi assrar
Did you get the six packs working?
Cheers
Alan |
|
Terug naar boven |
|
 |
assrar

|
Geplaatst: Ma Feb 25, 2013 9:18 pm Onderwerp: |
|
|
flypast schreef: | Hi assrar
Did you get the six packs working?
Cheers
Alan |
Hi Alan & Engravity_Support,
Thanks for the follow-up, I may be late for the confirmation till the installation is completed .But i feel confident about the answer.
Now in the middle of confusion to wire the master caution switch. if you don't mind continue with me the solve the problem.i'm using the same board, i figured out that the center is for the lights, but what about the 3 1 2 4 does it have + & - to or what?
Thanks
assrar |
|
Terug naar boven |
|
 |
|