FAQFAQ   ZoekenZoeken   RegistrerenRegistreren 

Sixpack with a grey ribbon cable not colored
Ga naar pagina 1, 2  Volgende
 
Nieuw onderwerp plaatsen   Reageren    flyengravity.com - build your own jetliner Forumindex -> Electronics
Vorige onderwerp :: Volgende onderwerp  
Auteur Bericht
assrar
Flight Captain

BerichtGeplaatst: Zo Feb 10, 2013 10:22 pm    Onderwerp: Sixpack with a grey ribbon cable not colored Reageren met citaat

Hi,

I receive the AFDS, But with a grey ribbon cable not colored Embarassed .
i don't know which way to connect to the AFDS. i took a picture of it so if anybody know how to connect please tell me.

the first or the second one
1-

2-




thanks
Terug naar boven
Profiel bekijken Stuur privébericht
assrar
Flight Captain

BerichtGeplaatst: Zo Feb 10, 2013 10:24 pm    Onderwerp: Reageren met citaat

2-




thanks
Terug naar boven
Profiel bekijken Stuur privébericht
assrar
Flight Captain

BerichtGeplaatst: Zo Feb 10, 2013 10:41 pm    Onderwerp: Reageren met citaat

Sorry all what i meant in the above test is the SIX PACK recall.

Embarassed But where is the picture gone
Terug naar boven
Profiel bekijken Stuur privébericht
assrar
Flight Captain

BerichtGeplaatst: Zo Feb 10, 2013 10:44 pm    Onderwerp: Reageren met citaat

why i cant edit my posts in this forum Razz
Terug naar boven
Profiel bekijken Stuur privébericht
assrar
Flight Captain

BerichtGeplaatst: Zo Feb 10, 2013 10:53 pm    Onderwerp: Reageren met citaat

anyway this is the pictures

1- http://i12.photobucket.com/albums/a203/assrar/AFDS/SIXPACKrecall6_zps924b0d87.jpg

2- http://i12.photobucket.com/albums/a203/assrar/AFDS/SIXPACKrecall5_zpsa715a25f.jpg

3- http://i12.photobucket.com/albums/a203/assrar/AFDS/SIXPACKrecall2_zps4d0ab070.jpg
Terug naar boven
Profiel bekijken Stuur privébericht
Engravity_Support
Site Admin

nl.gif

BerichtGeplaatst: Zo Feb 10, 2013 11:59 pm    Onderwerp: Reageren met citaat

if you look at the six packs from the back, the most left pin is the ground for the recal switch. The most right pin is the common cathode for the leds.

You can use the picture below for reference.

http://home.casema.nl/pago/sixb.JPG

if you have a multimeter with a continuity test, measure 2 pins on either end. press one of the recall buttons and see if it closes. if it closes you have found the 2 terminals for the recall. from there you can use the diagram in the manual to see the other connections.
_________________
www.flyengravity.com
Build your own jetliner
Terug naar boven
Profiel bekijken Stuur privébericht
flypast

BerichtGeplaatst: Ma Feb 11, 2013 12:52 am    Onderwerp: Reageren met citaat

Hi Assrar

I've just fitted the six packs quite easily with the grey ribbon cable.

The red one is the common cathode, so it follows that the next cable will connect one of the LED anunciators to your card.

For example cable 1 (common cathode red)
Cable 2 (next to common cathode (red)) will be the APU annunciator
Cable 3 will be the FLT CONT annunciator and so on and so on.

These aren't necessarily the order the the annunciators are wired but hopefully it will give you an idea.

Hope that makes sense.
Alan
Terug naar boven
assrar
Flight Captain

BerichtGeplaatst: Ma Feb 11, 2013 4:56 pm    Onderwerp: Reageren met citaat

Thank You Support and thank you flypast,
I will follow you and post the result.

assrar
Terug naar boven
Profiel bekijken Stuur privébericht
assrar
Flight Captain

BerichtGeplaatst: Di Feb 12, 2013 12:47 pm    Onderwerp: Reageren met citaat

Engravity_Support schreef:
if you look at the six packs from the back, the most left pin is the ground for the recal switch. The most right pin is the common cathode for the leds.

You can use the picture below for reference.

http://home.casema.nl/pago/sixb.JPG

if you have a multimeter with a continuity test, measure 2 pins on either end. press one of the recall buttons and see if it closes. if it closes you have found the 2 terminals for the recall. from there you can use the diagram in the manual to see the other connections.


He Engravity_Support and Mr.Alan,

Just to make sure the wiring is correct before i connect the cable.



Switch
======
cable - board
1-1
2-2
-------------------
LED
===
cable - board
9-1
8-2
7-3
6-4
5-5
4-6
3-7

assrar
Terug naar boven
Profiel bekijken Stuur privébericht
flypast

BerichtGeplaatst: Di Feb 12, 2013 4:00 pm    Onderwerp: Reageren met citaat

Hi Assrar

what board are you using?

Alan
Terug naar boven
assrar
Flight Captain

BerichtGeplaatst: Di Feb 12, 2013 10:25 pm    Onderwerp: Reageren met citaat

Hi Alan,

I'm using FDS-SYS4X.
http://www.flightdecksolutions.com/_assets/images/products/701-large.jpg

and this is the diagram,

http://i12.photobucket.com/albums/a203/assrar/AFDS/10987654321_zps718e9e37.png



assrar
Terug naar boven
Profiel bekijken Stuur privébericht
flypast

BerichtGeplaatst: Di Feb 12, 2013 11:26 pm    Onderwerp: Reageren met citaat

Hi assrar

Looks good to me. Go for it.

Let me know how you get on.

Cheers

Alan
Terug naar boven
Engravity_Support
Site Admin

nl.gif

BerichtGeplaatst: Vr Feb 15, 2013 2:21 am    Onderwerp: Reageren met citaat

yup,

1 (red) + 2 for the switch
3-8 LED anode
9 Led cathode
_________________
www.flyengravity.com
Build your own jetliner
Terug naar boven
Profiel bekijken Stuur privébericht
flypast

BerichtGeplaatst: Za Feb 16, 2013 8:16 pm    Onderwerp: Reageren met citaat

Hi assrar

Did you get the six packs working?

Cheers

Alan
Terug naar boven
assrar
Flight Captain

BerichtGeplaatst: Ma Feb 25, 2013 9:18 pm    Onderwerp: Reageren met citaat

flypast schreef:
Hi assrar

Did you get the six packs working?

Cheers

Alan


Hi Alan & Engravity_Support,

Thanks for the follow-up, I may be late for the confirmation till the installation is completed .But i feel confident about the answer. Razz

Now in the middle of confusion to wire the master caution switch. if you don't mind continue with me the solve the problem.i'm using the same board, i figured out that the center is for the lights, but what about the 3 1 2 4 does it have + & - to or what?

Thanks

assrar
Terug naar boven
Profiel bekijken Stuur privébericht
Berichten van afgelopen:   
Nieuw onderwerp plaatsen   Reageren    flyengravity.com - build your own jetliner Forumindex -> Electronics Tijden zijn in GMT + 2 uur
Ga naar pagina 1, 2  Volgende
Pagina 1 van 2

 
Ga naar:  
Je mag geen nieuwe onderwerpen plaatsen in dit subforum
Je mag geen reacties plaatsen in dit subforum
Je mag je berichten niet bewerken in dit subforum
Je mag je berichten niet verwijderen in dit subforum
Je mag niet stemmen in polls in dit subforum


Powered by Inforaction internet services. Based on phpBB © 2001, 2005 phpBB Group